Error code 0x0000007e is one of the most complicated error codes on your Windows Operating System that usually strikes because of misconfigured system files. This error is one of the Hexadecimal setups of blue screen error codes accepted by Windows as well as other software and driver vendors acceptable to Windows. The 0x0000007e error code addresses the memory location resulting in damage or corruption of Windows system files. So, if you’re dealing with this annoying situation and you don’t know what to do and how to get out of this critical situation, this article will certainly guide you in every way you can. We will share all the likely causes and effective solutions in this content to eliminate this code of error as soon as possible.
Probable Causes for why Error Code 0x0000007e Occurs on Windows 7?
If your PC is a 0x0000007e error victim, then this error code may have several likely causes. This problem usually occurs because your computer has damaged system files or the files have been lost. Incomplete software installation or uninstallation will also be a prime suspect for this code of error. If you have unsuccessfully deleted any hardware or mistakenly turned off the computer directly from the power socket, error code 0x0000007e will result. Sometimes this issue will also be addressed by a corrupted Windows registry or application files. However, by implementing some of the effective hacks that we will explore in the next segment, you can easily remove this error code.
Methods to Fix Windows Error Code 0x0000007e
In order to fix error code 0x0000007e in minutes, we have arranged several effective methods. You can go through either one or all of these methods until the error is fixed.
Method 1: Verify if Sufficient Space is Available on Hard Drive
You need to check if there is sufficient space on your hard drive as the limited hard disk space is the prime cause for this error. Go through the steps below in order to accomplish the task.
- At first, if the computer is turned on, restart the device manually.
- Now, when the computer logo appears on the screen, press the F8 key immediately to load the Recovery Screen.
- After that, navigate to the Advanced Repair Options from the list and click on that to open the Action.
- Click on Troubleshoot option on the next screen and then click on Advanced Option.
- Now, locate the Windows Startup Settings from the table and click on that to open the action.
- Click on the space available on the hard drive from the very bottom of the list and click on OK to proceed next.
- At last, close all the tabs normally after checking the disk space on your computer.
After successfully completing all the above steps, restart the computer and see if the error exists or not. If still, the error continues or the method doesn’t work, try another solution below.
Method 2: Update the BIOS on your Computer
If you have an outdated BIOS version on your computer, you may trigger the 0x0000007e error code on your computer. To remove this error, you need to update the BIOS version. Go through the steps below to fulfill the task.
Downloading the BIOS File
- At first, turn on your computer and tap the Windows start button at the left bottom corner of the window.
- Type “msinfo” into the search bar and tap the Enter key to invoke the System Information on the next window.
- Now, locate the System Model option on the screen and copy the computer’s model name and number.
- After that, navigate to the BIOS version number on your desktop. On the other hand, if you have a custom-built computer, simply skip this step.
- Now, open a web browser on your desktop and drive to the manufacturer’s website to download the BIOS file.
- Enter the BIOS version number, Model number, and Model name in the box and tap the Enter key to search for the latest BIOS version.
- You can see a list of all the options on the next screen. Simply click on Download button at the very bottom of the page.
- Next, click on Confirm option to begin the BIOS download for your desktop.
Installing the BIOS
- After the download completes, move to the Drive/Folder where you have saved the BIOS file and simply open the folder.
- Copy all the files to a USB drive and restart the computer to begin the process.
- When the logo appears on the startup screen, simply press the F12 key to enter the BIOS setup page.
- Select the BOOT tab from the screen and ensure that your USB drive is showing up with the Flash option.
- Select the Flash option from the Advanced tab and allow your computer to update the BIOS.
- Double-click on the BIOS.exe file and select the Extract option from the list.
- Now, click on Run and then on Next to begin the installation process.
- Click on the Accept all the Terms and Conditions checkbox and then click on Next option until the software application begins to install.
- Do not turn off the computer while the BIOS is updating and click on Finish button after the BIOS installation is completed.
After all the above steps have been completed successfully, restart your computer and see if the error code has been resolved. If you are still facing a problem or the method above is not working, try another solution below.
Method 3: Disable Device Drivers
Sometimes disabling the device drivers helps to fix certain error codes including error code 0x0000007e. Go through the steps below in order to accomplish the task.
- At first, turn on your computer and tap the Windows Start button on the left-bottom corner of the screen.
- Type Control Panel in the search box and tap the Enter key to open the action.
- When the Control Panel opens on the next screen, make your way to the System and Security option from the list.
- Click on System and then click on Advanced System Settings from the left sidebar of the window.
- Now, select the Hardware tab from the right-top corner of the screen and tap the Device Installation Settings button.
- At last, select NO and tap the Save button from the very bottom of the screen to save the changes.
After successfully completing all the above steps, restart your computer and see if the error code 0x0000007e is resolved. If still, the error exists or the above method doesn’t work, try the next solution described below.
Method 4: Remove all the Third-party Drivers from your Computer
If none of the above methods worked, you must uninstall all corrupted or faulty third-party drivers. One of the most common causes for this error is a corrupted driver or a faulty driver. To eliminate the error, go through the steps below.
- At first, turn on your computer and tap the Windows Start button on the left-bottom corner of the screen.
- Type Control Panel in the search box and tap the Enter key to open the action.
- When the Control Panel opens, move to the Device Manager option from the right side of the screen.
- Expand the Window and click on Uninstall Devices and Drivers to proceed next.
- Locate all the Third-party application drivers from the application list and right-click on the file.
- After that, select the Uninstall option and then tap on Confirm button to complete the Uninstallation process.
Do the same process one-by-one for all the applications to remove them completely from your desktop. After successfully completing all the above steps, restart your computer and see if the error code is resolved.
Conclusion
We shared all the effective ways in which Windows 70x0000007e error can be eliminated in no time. You can either go through one or all of these solutions until the 0x0000007e error stops. Hopefully the above article was good enough to guide you on how to permanently settle this issue on your computer. If the error code is still going on or the above methods are not working, then there may be some other internal problems or the hard drive will be corrupted. In that case, for further assistance, you can positively take assistance from an expert or consult with a technician. Finally, in the comment segment, we advise you to drop your valuable feedback below to let us know about your experience.
Google Drive Error 6248: Fix The Error Code With Easy Tech Hacks
